MiniCPU の履歴(No.5)

履歴一覧
差分を表示
現在との差分を表示
ソースを表示
MiniCPU へ行く。
- 1 (2015-09-03 (木) 23:41:29)
- 2 (2015-09-03 (木) 23:49:20)
- 3 (2015-09-09 (水) 15:32:10)
- 4 (2015-09-09 (水) 23:47:51)
- 5 (2015-09-10 (木) 16:39:17)

背景, 概要†

I2Cのデバイスを、スイッチを手で ON/OFF して、間違えずに操作するのは大変。自動化したい。
I2Cのデバイスを、高速（一秒間に１０回以上）に「手」で操作するのはほぼ不可能。高速化したい。
tiny CPU でプログラムを実行することができるけど、tiny CPU は配列を操作することは苦手。
配列に格納されたデータに従って、I2Cバスを操作したり、I2Cバスから入力されたデータを配列に格納したりすることができれば、便利。
tiny CPU をちょっと拡張して、配列を使えるようにしてみる。この拡張した tiny CPUを mini CPU と呼ぶ。
min CPU の命令セット、verilog など。ただし、verilog のコードを見る前に、自分で考えてみてください。
- http://www.cs.hiroshima-u.ac.jp/~nakano/wiki/wiki.cgi?page=%B9%E2%B5%A1%C7%BDMINICPU

verilog の例†

ram.v には、配列 C に 0,1,2,3 を入れて、そのあと配列 C の内容と配列 D の内容を出力するプログラムが入っています。
tinyCPUと同じように動かします。
各モジュールの先頭に, 適宜,
```
`timescale 1ns / 1ps
```
を入れてください。

top.v

module top(sSegAnode, sSegCathode, sw, led, bu, bd, bl, br, bc, bclck
    );
  output [7:0] sSegAnode;
  output [7:0] sSegCathode;
  output [15:0] led;
  input [15:0] sw;
  input bu, bd, bl, br, bc, bclck;
  wire BNx, BWx, BEx, BCx;
  wire reset;
  assign reset=~bd; 

  reg clk, run;
  reg [15:0] in;
  wire [2:0] cs;
  wire [15:0] irout, qtop, dbus, out;
  wire [11:0] pcout, abus;

  
  
  chattering #(4) chattering0(.clk(bclck), .reset(reset), .in({bu,bl,br,bc}), .out({BNx,  BWx, BEx, BCx}));
//  assign BNx=BN;
//  assign BWx=BW;
//  assign BEx=BE;
//  assign BCx=BC;
  sSegArray sSegArray0(.clk(bclck), .reset(reset), .load(clk), 
 .d({{1{0}},cs,abus,dbus}),
  .anode(sSegAnode), .cathode(sSegCathode));
  
  always @(posedge BCx, negedge reset) begin
     if(!reset) clk<=0;
	  else
	    clk<=~clk;
  end
  
  minicpu minicpu0(.clk(clk), .reset(reset), .run(BNx), .in(sw), .cs(cs), 
          .pcout(pcout), .irout(irout), .qtop(qtop), .abus(abus), .dbus(dbus), .out(led));
endmodule

defs.v

`define IDLE 3'b000
`define FETCHA 3'b001
`define FETCHB 3'b010
`define EXECA 3'b011
`define EXECB 3'b100
`define ADD 5'b00000
`define SUB 5'b00001
`define MUL 5'b00010
`define SHL 5'b00011
`define SHR 5'b00100
`define BAND 5'b00101
`define BOR 5'b00110
`define BXOR 5'b00111
`define AND 5'b01000
`define OR 5'b01001
`define EQ 5'b01010
`define NE 5'b01011
`define GE 5'b01100
`define LE 5'b01101
`define GT 5'b01110
`define LT 5'b01111
`define NEG 5'b10000
`define BNOT 5'b10001
`define NOT 5'b10010
`define HALT 4'b0000
`define PUSHI 4'b0001
`define PUSH 4'b0010
`define POP 4'b0011
`define JMP 4'b0100
`define JZ 4'b0101
`define JNZ 4'b0110
`define LD 4'b0111 
`define ST 4'b1000
`define IN 4'b1101
`define OUT 4'b1110
`define OP 4'b1111

minicpu.v (高速化してません。)

`include "defs.v"
module minicpu(clk, reset, run, in, cs, pcout, irout, qtop, abus, dbus, out
);
input clk,reset, run;
input [15:0] in;
output [2:0] cs;
output [15:0] irout, qtop, dbus, out;
output [11:0] pcout, abus;
wire [15:0] qnext, ramout, aluout;
reg [11:0] abus;
reg halt, cont, pcinc, push, pop, abus2pc, dbus2ir, dbus2qtop, dbus2ram,
dbus2obuf, pc2abus, ir2abus, ir2dbus, qtop2dbus, qnext2dbus, qtop2abus,  qnext2abus, alu2dbus, ram2dbus, in2dbus;
counter #(12) pc0(.clk(clk), .reset(reset), .load(abus2pc),
.inc(pcinc), .d(abus), .q(pcout));
counter #(16) ir0(.clk(clk), .reset(reset), .load(dbus2ir), 
.inc(0), .d(dbus), .q(irout));
state state0(.clk(clk), .reset(reset), .run(run),
.halt(halt), .cont(cont), .cs(cs));
stack stack0(.clk(clk), .reset(reset), .load(dbus2qtop), .push(push), .pop(pop),
.d(dbus), .qtop(qtop), .qnext(qnext));
alu alu0(.a(qtop), .b(qnext), .f(irout[4:0]), .s(aluout));
ram #(16,12,4096) ram0(.clk(clk), .load(dbus2ram),
.addr(abus), .d(dbus), .q(ramout));
counter #(16) obuf0(.clk(clk), .reset(reset), .load(dbus2obuf),
.inc(0), .d(dbus), .q(out));

always @(pc2abus or ir2abus or pcout or irout or qtop2abus or qnext2abus)
  if(pc2abus) abus = pcout;
  else if(ir2abus) abus = irout[11:0];
  else if(qtop2abus) abus = qtop[11:0];
  else if(qnext2abus) abus = qnext[11:0]; 
  else abus = 12'hxxx;

assign dbus = ir2dbus ? {{4{irout[11]}},irout[11:0]} : 16'hzzzz;
assign dbus = qtop2dbus ? qtop : 16'hzzzz;
assign dbus = alu2dbus ? aluout : 16'hzzzz;
assign dbus = ram2dbus ? ramout : 16'hzzzz;
assign dbus = in2dbus ? in : 16'hzzzz;
assign dbus = qnext2dbus? qnext[11:0] : 16'hzzz;

always @(cs or irout or qtop)
 begin
  halt = 0; cont = 0; pcinc = 0; push = 0; pop = 0; abus2pc = 0; dbus2ir = 0;
  dbus2qtop = 0; dbus2ram = 0; dbus2obuf = 0; pc2abus = 0; ir2abus = 0;  qtop2abus = 0;
  ir2dbus = 0; qtop2dbus = 0; alu2dbus = 0; ram2dbus = 0; in2dbus = 0; qnext2dbus=0; qnext2abus=0;
  if(cs == `FETCHA)
  begin
    pcinc = 1; pc2abus = 1;
  end
  else if(cs == `FETCHB)
  begin
    ram2dbus = 1; dbus2ir = 1;
  end
  else if(cs == `EXECA)
  case(irout[15:12])
    `PUSHI:
    begin
      ir2dbus = 1; dbus2qtop = 1; push = 1;
    end
    `PUSH:
    begin
       ir2abus = 1; cont = 1;
    end
    `LD:
    begin
       qtop2abus = 1; cont = 1; pop=1;
    end
    `POP:
    begin
      ir2abus = 1; qtop2dbus =1; dbus2ram = 1; pop = 1;
    end
    `ST:
    begin
      qtop2dbus = 1;  dbus2ram=1; qnext2abus=1; pop = 1; cont=1;
    end
    `JMP:
    begin
      ir2abus = 1; abus2pc = 1;
    end
    `JZ: 
    begin
      if(qtop==0)
      begin
        ir2abus = 1; abus2pc = 1;
      end
      pop = 1;
    end 
    `JNZ:
    begin
    if(qtop !=0)
      begin
        ir2abus = 1; abus2pc = 1;
      end
      pop = 1;
    end
     `IN:
    begin
      in2dbus = 1; dbus2qtop = 1; push = 1;
    end
    `OUT:
    begin
      qtop2dbus = 1; dbus2obuf = 1; pop = 1;
    end
    `OP:
    begin
      alu2dbus = 1; dbus2qtop = 1;
      if(irout[4] ==0) pop = 1;
    end
    default:
      halt = 1;
  endcase
  else if(cs == `EXECB)
    begin
    if(irout[15:12] == `PUSH|| irout[15:12] == `LD)
      begin
        ram2dbus = 1; dbus2qtop = 1; push = 1;
      end
    else
    if(irout[15:12] == `ST)
      begin
        pop = 1;
      end
    end
end 

endmodule

state.v

`include "defs.v"
module state(clk, reset, run, cont, halt, cs
);
input clk, reset, run, cont, halt;
output [2:0] cs;
reg [2:0] cs;

always @(posedge clk or negedge reset)
 if(!reset) cs<= `IDLE;
 else
 case(cs)
  `IDLE: if(run) cs <= `FETCHA;
  `FETCHA: cs <= `FETCHB;
  `FETCHB: cs <= `EXECA;
  `EXECA: if(halt) cs <= `IDLE;
          else if(cont) cs <= `EXECB;
          else cs <= `FETCHA;
  `EXECB: cs <= `FETCHA;
  default: cs <= 3'bxxx;
 endcase

endmodule

stack.v

module stack(clk, reset, load, push, pop, d, qtop, qnext );
 parameter N=8;
 input clk, reset, load, push, pop;
 input [15:0] d;
 output [15:0] qtop, qnext;
 reg [15:0] q [N-1:0];

 assign qtop = q[0];
 assign qnext = q[1];

 always @(posedge clk or negedge reset)
   if(!reset) q[0] <= 0;
   else if(load) q[0] <= d;
   else if(pop) q[0] <= q[1];

 //integer i;
 generate
 genvar i;
   for(i=1;i<N-1; i=i+1)
   begin : for_i
     always @(posedge clk or negedge reset)
       if(!reset) q[i] <=0;
       else if(push) q[i] <=q[i-1];
       else if(pop) q[i] <=q[i+1];
   end
 endgenerate

 always @(posedge clk or negedge reset)
   if(!reset) q[N-1] <= 0;
   else if(push) q[N-1] <= q[N-2];

endmodule

alu.v

`include "defs.v"
module alu(a,b,f,s);
 input [15:0] a,b;
 input [4:0] f;
 output [15:0] s;
 reg [15:0] s;
 wire [15:0] x,y;
 assign x=a+16'h8000;
 assign y=b+16'h8000;
 always @(a or b or x or y or f)
  case(f)
   `ADD : s = b + a;
   `SUB : s = b - a;
   `MUL : s = b * a;
   `SHL : s = b << a;
   `SHR : s = b >> a;
   `BAND : s = b & a;
   `BOR : s = b | a;
   `BXOR : s = b ^ a;
   `AND : s = b && a;
   `OR : s = b || a;
   `EQ : s = b == a;
   `NE : s = b != a;
   `GE : s = x >= y;
   `LE : s = x <= y;
   `GT : s = x > y;
   `LT : s = x < y;
   `NEG : s= -a;
   `BNOT : s= ~a;
   `NOT : s = !a;
   default : s = 16'hxxxx;
  endcase
endmodule

ram.v

module ram(clk, load, addr, d, q
);
 parameter DWIDTH=16, AWIDTH=12, WORDS=4096; 
 
 input clk, load;
 input [AWIDTH-1:0] addr;
 input [DWIDTH-1:0] d;
 output [DWIDTH-1:0] q;
 reg [DWIDTH-1:0] q;
 reg [DWIDTH-1:0] mem [WORDS-1:0];
 
 always @(posedge clk)
  begin
   if(load) mem[addr] <= d;
   q <= mem[addr];
  end
 
 integer i;
 initial begin
   for(i=0; i<WORDS; i=i+1)
     mem[i]=12'h000;
 mem[8'h00] = 16'h1000; //      PUSHI 0
 mem[8'h01] = 16'h3021; //      POP  i  ... i=0;
 mem[8'h02] = 16'h2021; // L1   PUSH i
 mem[8'h03] = 16'h1023; //      PUSHI C
 mem[8'h04] = 16'hF000; //      ADD
 mem[8'h05] = 16'h2021; //      PUSH i   
 mem[8'h06] = 16'h8000; //      ST     ... C[i]=i;
 mem[8'h07] = 16'h2021; //      PUSH i
 mem[8'h08] = 16'h1001; //      PUSHI 1
 mem[8'h09] = 16'hF000; //      ADD     
 mem[8'h0A] = 16'h3021; //      POP i    .... i++;
 mem[8'h0B] = 16'h2021; //      PUSH i
 mem[8'h0C] = 16'h201F; //      PUSH n
 mem[8'h0D] = 16'hF001; //      SUB
 mem[8'h0E] = 16'h6002; //      JNZ L1:   if(i<n) goto L1;
 mem[8'h0F] = 16'h1000; //      PUSHI 0
 mem[8'h10] = 16'h3022; //      POP  j    .... j=0;
 mem[8'h11] = 16'h2022; // L2:  PUSH j
 mem[8'h12] = 16'h1023; //      PUSHI C
 mem[8'h13] = 16'hF000; //      ADD
 mem[8'h14] = 16'h7000; //      LD    
 mem[8'h15] = 16'hE000; //      OUT        print(C[j]);
 mem[8'h16] = 16'h2022; //      PUSH j
 mem[8'h17] = 16'h1001; //      PUSHI 1
 mem[8'h18] = 16'hF000; //      ADD
 mem[8'h19] = 16'h3022; //      POP j       j++
 mem[8'h1A] = 16'h2022; //      PUSH j
 mem[8'h1B] = 16'h2020; //      PUSH m
 mem[8'h1C] = 16'hF001; //      SUB
 mem[8'h1D] = 16'h6011; //      JNZ L2:    if(j<m) goto L2
 mem[8'h1E] = 16'h0000; // L3:  HALT
 mem[8'h1F] = 16'h0004; // n:   4
 mem[8'h20] = 16'h0010; // m:  16
 mem[8'h21] = 16'h0000; // i:
 mem[8'h22] = 16'h0000; // j:    0
 mem[8'h23] = 16'h0000; // C:  
 mem[8'h24] = 16'h0000; //
 mem[8'h25] = 16'h0000; //
 mem[8'h26] = 16'h0000; //
 mem[8'h27] = 16'h0001; // D:   1
 mem[8'h28] = 16'h0000; //      0
 mem[8'h29] = 16'h0002; //      2
 mem[8'h2A] = 16'h0000; //      0
 mem[8'h2B] = 16'h0004; //      4
 mem[8'h2C] = 16'h0000; //      0
 mem[8'h2D] = 16'h0005; //      5
 mem[8'h2E] = 16'h0000; //      0
 mem[8'h2F] = 16'h000A; //      A
 mem[8'h30] = 16'h0000; //      0
 mem[8'h31] = 16'h0008; //      8
 mem[8'h32] = 16'h0000; //      0
end
endmodule

counter.v

module counter(clk, reset, load, inc, d, q );
 parameter N=16;
 
 input clk, reset, load, inc;
 input [N-1:0] d;
 output [N-1:0] q;
 reg [N-1:0] q;
 
 always @(posedge clk or negedge reset)
   if(!reset) q <=0;
   else if(load) q<=d;
   else if(inc) q<=q+1;
endmodule

chattering.v

module chattering(clk, reset, in, out
);
 parameter N=1;
 input clk, reset;
 input [N-1:0]in;
 output [N-1:0]out;
 reg [N-1:0]out;
 reg [21:0] count;

 always @(posedge clk or negedge reset)
  if(!reset) count <=0;
  else count <= count +1;

 always @(posedge clk)
  if(count==0) out <= in;

endmodule

sSegArray.v

module sSegArray(
    clk,reset,load,d, 
	 anode, cathode
    );
parameter N=32;
input clk,reset,load;
input [N-1:0] d;
output [7:0] anode;
output [7:0] cathode;
reg [7:0] anode;
reg [7:0] cathode;
reg [31:0] q; 

wire [2:0] selectedSeg;
wire [7:0] wOneSeg;
reg segClk; 

counter #(8) waitOneSeg(.clk(clk), .reset(reset), .load(0), .inc(1), .d(16'h0000), .q(wOneSeg));

//assign segClk= (wOneSeg==0)? ~segClk: segClk;
always @(posedge clk, negedge reset) begin
  if(!reset) segClk<=0;
  else
  if (wOneSeg==0) segClk<=~segClk;
end

counter #(3) selector(.clk(segClk),.reset(reset),.load(0), .inc(1), .d(4'h0), .q(selectedSeg));
//counter #(3) selector(.clk(clk), .reset(reset), .load(0), .inc(1), .d(4'h0), .q(selectedSeg));
 
always @(posedge clk, negedge reset)
 begin
  if(!reset) anode=8'hFE;   // note!  anode is connected by pnp transistor.  
  else                      // in order to active one 7seg, low should be setted to the 7seg. 
   case (selectedSeg)
	   3'b000: anode=8'hFE;
		3'b001: anode=8'hFD;
		3'b010: anode=8'hFB;
		3'b011: anode=8'hF7;
		3'b100: anode=8'hEF;
		3'b101: anode=8'hDF;
		3'b110: anode=8'hBF;
		3'b111: anode=8'h7F;
	endcase
end

reg [3:0] selectedVal; 

always @(posedge clk, negedge reset)
  begin
   if(!reset) cathode=8'h03;                   // note! when one segment of the cathode is low,
   else                                        //  and its anode is low, the segment glow.
   case (selectedVal)                         //          ca
     4'b0000: cathode=8'h03;   //8'hfc; 0              ------
     4'b0001: cathode=8'h9f;   //8'h60; 1              /     /
     4'b0010: cathode=8'h25;   //8'hda; 2              /cf   / cb
 	 4'b0011: cathode=8'h0d;   //8'hf2; 3              /     /
 	 4'b0100: cathode=8'h99;   //8'h66; 4               -----  
	 4'b0101: cathode=8'h49;   //8'hb6; 5              /  cg  /
 	 4'b0110: cathode=8'h41;   //8'hbe; 6              /ce    / cc
 	 4'b0111: cathode=8'h1f;   //8'he0; 7              /      /
 	 4'b1000: cathode=8'h01;   //8'hfe; 8               ------     . ch
 	 4'b1001: cathode=8'h09;   //8'hf6; 9                  cd
 	 4'b1010: cathode=8'h11;   //8'hee; A
 	 4'b1011: cathode=8'hc1;   //8'h3e; B
 	 4'b1100: cathode=8'h63;   //8'h9c; C
 	 4'b1101: cathode=8'h85;   //8'h7c; D
 	 4'b1110: cathode=8'h61;   //8'h9e; E
 	 4'b1111: cathode=8'h71;   //8'h8e; F
 	endcase
 end

always @(posedge clk, negedge reset)
 begin
   if(!reset) selectedVal=q[3:0];
   else
    case (selectedSeg)
 	  3'b000: selectedVal=q[3:0];
 	  3'b001: selectedVal=q[7:4];
 	  3'b010: selectedVal=q[11:8];
 	  3'b011: selectedVal=q[15:12];
 	  3'b100: selectedVal=q[19:16];
 	  3'b101: selectedVal=q[23:20];
 	  3'b110: selectedVal=q[27:24];
 	  3'b111: selectedVal=q[31:28];
 	endcase
 end

always @(posedge clk, negedge reset)
 begin
   if(!reset) q=0;
   else
   if(load) q=d;
 end

endmodule

top.ucf

## This file is a general .ucf for the Nexys4 rev B board
## To use it in a project:
## - uncomment the lines corresponding to used pins
## - rename the used signals according to the project

## Clock signal
NET "bclck"   LOC = "E3"	| IOSTANDARD = "LVCMOS33";					#Bank = 35, Pin name = IO_L12P_T1_MRCC_35,					Sch name = CLK100MHZ
#NET "clk" TNM_NET = sys_clk_pin;
#TIMESPEC TS_sys_clk_pin = PERIOD sys_clk_pin 100 MHz HIGH 50%; 
 
## Switches
NET "sw<0>"			LOC = "U9"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L21P_T3_DQS_34,					Sch name = SW0
NET "sw<1>"			LOC = "U8"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_25_34,							Sch name = SW1
NET "sw<2>"			LOC = "R7"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L23P_T3_34,						Sch name = SW2
NET "sw<3>"			LOC = "R6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L19P_T3_34,						Sch name = SW3
NET "sw<4>"			LOC = "R5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L19N_T3_VREF_34,					Sch name = SW4
NET "sw<5>"			LOC = "V7"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L20P_T3_34,						Sch name = SW5
NET "sw<6>"			LOC = "V6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L20N_T3_34,						Sch name = SW6
NET "sw<7>"			LOC = "V5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L10P_T1_34,						Sch name = SW7
NET "sw<8>"			LOC = "U4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L8P_T1-34,						Sch name = SW8
NET "sw<9>"			LOC = "V2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L9N_T1_DQS_34,					Sch name = SW9
NET "sw<10>"			LOC = "U2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L9P_T1_DQS_34,					Sch name = SW10
NET "sw<11>"			LOC = "T3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L11N_T1_MRCC_34,					Sch name = SW11
NET "sw<12>"			LOC = "T1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L17N_T2_34,						Sch name = SW12
NET "sw<13>"			LOC = "R3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L11P_T1_SRCC_34,					Sch name = SW13
NET "sw<14>"			LOC = "P3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L14N_T2_SRCC_34,					Sch name = SW14
NET "sw<15>"			LOC = "P4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L14P_T2_SRCC_34,					Sch name = SW15

## LEDs
NET "led<0>"			LOC = "T8"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L24N_T3_34,						Sch name = LED0
NET "led<1>"			LOC = "V9"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L21N_T3_DQS_34,					Sch name = LED1
NET "led<2>"			LOC = "R8"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L24P_T3_34,						Sch name = LED2
NET "led<3>"			LOC = "T6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L23N_T3_34,						Sch name = LED3
NET "led<4>"			LOC = "T5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L12P_T1_MRCC_34,					Sch name = LED4
NET "led<5>"			LOC = "T4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L12N_T1_MRCC_34,					Sch	name = LED5
NET "led<6>"			LOC = "U7"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L22P_T3_34,						Sch name = LED6
NET "led<7>"			LOC = "U6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L22N_T3_34,						Sch name = LED7
NET "led<8>"			LOC = "V4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L10N_T1_34,						Sch name = LED8
NET "led<9>"			LOC = "U3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L8N_T1_34,						Sch name = LED9
NET "led<10>"			LOC = "V1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L7N_T1_34,						Sch name = LED10
NET "led<11>"			LOC = "R1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L17P_T2_34,						Sch name = LED11
NET "led<12>"			LOC = "P5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L13N_T2_MRCC_34,					Sch name = LED12
NET "led<13>"			LOC = "U1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L7P_T1_34,						Sch name = LED13
NET "led<14>"			LOC = "R2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L15N_T2_DQS_34,					Sch name = LED14
NET "led<15>"			LOC = "P2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L15P_T2_DQS_34,					Sch name = LED15

#NET "RGB1_Red"			LOC = "K5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L5P_T0_34,						Sch name = LED16_R
#NET "RGB1_Green"		LOC = "F13"	| IOSTANDARD = "LVCMOS33";		#Bank = 15, Pin name = IO_L5P_T0_AD9P_15,					Sch name = LED16_G
#NET "RGB1_Blue"		LOC = "F6"	| IOSTANDARD = "LVCMOS33";		#Bank = 35, Pin name = IO_L19N_T3_VREF_35,					Sch name = LED16_B
#NET "RGB2_Red"			LOC = "K6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_0_34,								Sch name = LED17_R
#NET "RGB2_Green"		LOC = "H6"	| IOSTANDARD = "LVCMOS33";		#Bank = 35, Pin name = IO_24P_T3_35,						Sch name =  LED17_G
#NET "RGB2_Blue"		LOC = "L16"	| IOSTANDARD = "LVCMOS33";		#Bank = CONFIG, Pin name = IO_L3N_T0_DQS_EMCCLK_14,			Sch name = LED17_B

## 7 segment display
NET "sSegCathode<7>"			LOC = "L3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L2N_T0_34,						Sch name = CA
NET "sSegCathode<6>"			LOC = "N1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L3N_T0_DQS_34,					Sch name = CB
NET "sSegCathode<5>"			LOC = "L5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L6N_T0_VREF_34,					Sch name = CC
NET "sSegCathode<4>"			LOC = "L4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L5N_T0_34,						Sch name = CD
NET "sSegCathode<3>"			LOC = "K3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L2P_T0_34,						Sch name = CE
NET "sSegCathode<2>"			LOC = "M2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L4N_T0_34,						Sch name = CF
NET "sSegCathode<1>"			LOC = "L6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L6P_T0_34,						Sch name = CG

NET "sSegCathode<0>"				LOC = "M4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L16P_T2_34,						Sch name = DP

NET "sSegAnode<0>"			LOC = "N6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L18N_T2_34,						Sch name = AN0
NET "sSegAnode<1>"			LOC = "M6"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L18P_T2_34,						Sch name = AN1
NET "sSegAnode<2>"			LOC = "M3"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L4P_T0_34,						Sch name = AN2
NET "sSegAnode<3>"			LOC = "N5"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L13_T2_MRCC_34,					Sch name = AN3
NET "sSegAnode<4>"			LOC = "N2"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L3P_T0_DQS_34,					Sch name = AN4
NET "sSegAnode<5>"			LOC = "N4"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L16N_T2_34,						Sch name = AN5
NET "sSegAnode<6>"			LOC = "L1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L1P_T0_34,						Sch name = AN6
NET "sSegAnode<7>"			LOC = "M1"	| IOSTANDARD = "LVCMOS33";		#Bank = 34, Pin name = IO_L1N_T034,							Sch name = AN7

## Buttons
#NET "btnCpuReset"		LOC = "C12"	| IOSTANDARD = "LVCMOS33";		#Bank = 15, Pin name = IO_L3P_T0_DQS_AD1P_15,				Sch name = CPU_RESET
NET "bc"				LOC = "E16"	| IOSTANDARD = "LVCMOS33";		#Bank = 15, Pin name = IO_L11N_T1_SRCC_15,					Sch name = BTNC
NET "bu"				LOC = "F15"	| IOSTANDARD = "LVCMOS33";		#Bank = 15, Pin name = IO_L14P_T2_SRCC_15,					Sch name = BTNU
NET "bl"				LOC = "T16"	| IOSTANDARD = "LVCMOS33";		#Bank = CONFIG, Pin name = IO_L15N_T2_DQS_DOUT_CSO_B_14,	Sch name = BTNL
NET "br"				LOC = "R10"	| IOSTANDARD = "LVCMOS33";		#Bank = 14, Pin name = IO_25_14,							Sch name = BTNR
NET "bd"				LOC = "V10"	| IOSTANDARD = "LVCMOS33";		#Bank = 14, Pin name = IO_L21P_T3_DQS_14,					Sch name = BTND

Counter: 1910, today: 2, yesterday: 3